13kw High Expansion Foam Generator

Russian president demanded that exports of Russian gas to "unfriendly" countries be settled in rubles. The demand has raised concerns in Germany about possible supply disruptions and the impact on industry and households if utilities do not pay in robles. Europe gets about 40% of its gas from Russia. Last year, Europe imported about 155 billion cubic meters. Germany, Europe's largest economy, depends heavily on Russian gas.

The chief executive of Germany's E.ON said the German economy would face "significant damage, which should be avoided if possible" without Russian supplies. He also said it would take Germany three years to wean itself off Russian gas.  

In the event of a supply disruption, Germany's gas network regulator would prioritize home heating over industrial use, so energy-hungry manufacturers such as steelmakers would be the first to suffer, he said.

The volatile international situations will continue to affect the markets and prices of many commodities like the Foam Generator.

Performance parameters:

The 3kW foaming machine is a small cement foam generator. It is a special equipment specially used for producing foam in small factories. It is simple and convenient to operate. It is suitable for small factories, universities, colleges, scientific research institutes and other production departments to develop new products. It can also be used for medium-sized construction in decoration projects. 

Usage and installation method:

Power connection: This equipment uses a three-phase 220V power supply. After all the lines are connected, click the start button, and then immediately click the stop button to check the direction of rotation. Make sure that the direction of rotation of the motor is correct. If the direction of rotation of the motor is incorrect, The two live wires need to be exchanged arbitrarily, and don't connect them wrongly.

Note: The panel voltmeter will display after the wiring is completed and the power is turned on. When the display voltage is normal at 220V, the air switch can be closed at this time, and the device enters the operational state.

Pipeline connection: Please connect the water pipe and foaming agent straw to the corresponding interface at the front of the device. use Wrap the tape around the joint to prevent air leakage. If air leakage occurs, the foaming agent cannot be pumped or 

Insufficient flow affects the efficiency of bubble making.

Bubble tube: The bubble tube is external and detachable. The front end of the bubble tube is detachable to replace the steel ball filled in the tube. The operation is simple, convenient and quick when disassembling.

Usually need to be disassembled:

1. After working for a long time, it is found that the foam shape is not good, usually more than three months.

2. Pipe blockage: Some foaming agent remaining in the bubble tube will form a solid residue. In this case, the foam cannot be produced normally, or the pipeline pressure increases sharply. At this time, all the old steel balls need to be taken out, and then replaced with a new one The ball is fine. Steel wire ball specification requirements: each blowing tube needs to be filled with about 12-15 steel wire balls. Too much or too little will affect or even destroy the foam performance. 

Precautions:

1. Remember to use electricity safely. If water or foam touches the circuit, you must immediately cut off the power at the remote end to ensure safe production.

2. There will be air in the pipeline when it is used for the first time. The foaming liquid has not been pumped into the equipment in a short time. You can wait for tens of seconds until the liquid is filled with the entire suction tube and the foaming operation can be performed normally.

3. Do not start the equipment when the pipeline is blocked to prevent damage to the components due to overpressure in the pipeline.

Since the beginning of this year, China's macro policies have made continuous efforts to stabilize economic growth. America and Europe are raising interest rates to control inflation. On March the European Central Bank left its three key interest rates unchanged and began to scale back its asset-purchase programme. Then the Federal Reserve raised the target range of the federal funds rate by 25 basis points to 0.25%-0.5%. The accelerated tightening of monetary policies in the US and Europe pushed capital back to the US and increased interest rates, which will definitely increase the risk of RMB depreciation and capital outflow. The price and market of the Foam Generator will also be affected, resulting in a range of fluctuations. You are welcome to contact us for the latest quotation of Foam Generator.

Inquiry us